| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Every accent change brought the conky dashboard up from special:dash.
udt-accent rewrites conky.conf in place, which conky reloads, and then
runs hyprctl reload, which re-applies window rules to existing windows;
either path ends with this rule moving the dashboard to its special
workspace, and without silent that also shows the workspace. The exec
rule in autostart is silent but only covers the first window.
Which of the two paths fires was not settled: rewriting conky.conf by
hand kept the same window address, so a conky reload alone may not remap
it. silent covers both. Checked with hyprctl eval (accepted) and a
reload with no configerrors, and confirmed by eye: the dashboard stays hidden through accent changes.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
|
|
The quickshell keybind reminder lists hyprctl binds -j, which reports
Lua actions as an opaque handle, so a bind shows what it does only
through its description. This was the one bind left undescribed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
|
|
The workspace rule pinning special:dash to DP-1 does not work: special
workspaces ignore a workspace_rule's `monitor` and open on whichever
monitor has focus. Verified on 0.56.2; upstream hyprwm/Hyprland#7990 and
#5570, both closed in the issues-to-discussions migration rather than
fixed.
The comment claimed the opposite, which was convincing because the rule
does register and `hyprctl workspacerules` reports it enabled. The rule
stays, so the intent is recorded and the line is ready if upstream fixes
it, and the bind now names the manual step: focus DP-1 first.
Also notes that the window stays on DP-3 once opened there, so a later
toggle is cropped until it is moved back, the conky surface being a
fixed 2560x1080.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
|
|
The conky surface is a fixed 2560x1080, because Hyprland's fullscreen
rule resizes the window but not the drawing surface, so on the
1920-wide DP-3 the dashboard would be cropped. A workspace rule keeps it
on the primary monitor.
hl.workspace_rule takes `workspace`, not `match`, and has no `name`
field, unlike hl.window_rule. Both were checked against the runtime,
which rejects an unknown field with "unknown field '<name>'", and
hyprctl workspacerules confirms the rule registers with monitor: DP-1.
NOT fully verified: whether it holds when the toggle is pressed while
DP-3 has focus. One observation suggested the dashboard still followed
focus, but it was taken before the reload had applied the rule, and
focus could not afterwards be moved to DP-3 without a window or the
pointer on it. Every toggle since the reload has opened on DP-1. Worth
confirming after a fresh Hyprland start.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
|
|
Four defects, all found while running Task 8.
The documented toggle command does not work on this machine. Under the
Lua config `hyprctl dispatch` evaluates its argument as Lua, so the
plain `hyprctl dispatch togglespecialworkspace dash` fails with "')'
expected near 'dash'"; Hyprland even says so in its error. The working
form is `hyprctl dispatch 'hl.dsp.workspace.toggle_special("dash")'`,
verified toggling special:dash on and off. Also read the result from
`monitors[0].specialWorkspace.name`, since activeworkspace keeps
reporting the ordinary workspace underneath.
`fullscreen` and `no_focus` appear in no existing rule, so they were
checked against the runtime rather than left as caveats:
hl.window_rule rejects an unknown field with "unknown field '<name>'",
and neither produces that error, so both are accepted. A deliberate
bogus key confirmed the check itself works.
hl.mainMod is nil in any section other than keybindings.lua, which
declares `local mainMod = "SUPER"` and never exports it. The plan
hedged about this; it now states the literal to use.
Task 8's class check ran `conky -c ./conky.conf`, which is gitignored
generated output and absent on a fresh clone, so it now renders the
config first. Its `pkill -f` also matched the running script's own
command line and killed the shell's process group, returning 144 and
swallowing the log it had just been told to read; `pkill -x conky`
instead, fixed in Tasks 4 and 6 too.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
|
|
A Lua section, not a .conf fragment: the live Hyprland config is
hyprland.lua requiring sections/, with rules declared through the hl
helper API.
Pins conky-dash to its own special:dash workspace, fullscreen, no
border, no focus, and binds SUPER+S. Not SUPER+D, which keybindings.lua
already binds to the unnamed special workspace, and that workspace
already hosts the btop scratchpad.
no_focus matters because the dashboard starts with the session:
without it, it steals focus at login and can be tabbed to like an app.
autostart.lua already launches a bare conky, so the README says to
change that line rather than add one, which would run two instances.
Co-Authored-By: Claude Opus 5 <noreply@anthropic.com>
|
